What is rigging safety?

Rigging safety is the sum total of steps taken to reduce the risk of harm to persons when rigging. Precautions include proper training of staff, adequate personal protective equipment, routine inspections of equipment, environmental risk assessments, proven communication and emergency/backup procedures.

What are Rigger’s tasks and responsibilities?

Riggers are responsible for the use of ropes, pulleys and other devices, such as heavy chains, cables and straps, to secure heavy loads, which are then to be transported by means of a crane. Riggers have the experience they need when it comes to knowing which hooks to attach and how much weight various cranes can carry. They have a great understanding of the center of gravity of the load needed to ensure proper balance, stability and mobility of the load at all times.

To those unfamiliar with the construction site, the crane operator may appear to be the person with the greatest responsibility.The Rigger has just as much responsibility, if not more than the crane operator, as it is responsible for properly rigging and managing the load. Without an experienced rigger with rigging training in place and a correctly rigged load, the site can easily become a danger zone.

What are the Functions and Duties of the Rigger or the Dogger?

If the rigger has correctly rigged the load, it is the rigger’s responsibility to direct the crane operator safely in moving the load from its rigging position to where it needs to go. The rigger is the eyes and ears of the crane operator on the ground and is responsible for ensuring that all operations of the crane are carried out safely. This is achieved by using clear hand signals, which are understood by both the rigger and the crane operator.

A qualified riggeris responsible for:

• Inspect your facilities and rigging equipment
• In compliance with official standards and regulations and requirements
• Properly set up the cranes
• Meet the proper operating methods
• Understanding the load charts to know how much work a crane can do safely

How do you become a Rigger or Dogman?

In order to become a licensed rigger and or dogger, it is a requirement that a person must undergo one of the NCCCO job training courses in which he/she learns the techniques and responsibilities of the dogging, crane rigging and crane operation. You can do this by enrolling in a dogman course in Perth. Also the knowledge of hand signals and voice-activated and audible signals, the operation of the cranes and the fundamentals of rigging, load handling and other environmental factors. Individuals must pass both a written and practical exam provided by an approved organisation of the National Commission for the Certification of Crane Operators (NCCCO). The Rigger and dogman Credential is a document that indicates that someone has demonstrated their ability to perform the tasks expected of a skilled Rigger and dogman.

What is the Value of Safety When Running Construction Equipment?

Construction sites can be very risky for inexperienced individuals who are not well educated and trained to know how to deal with heavy machinery and cranes. A false move can easily lead to serious injury or even death.

The signal operator needs to know the types of signals used at the work site, to be able to use such signals competently, to know the crane equipment, its limitations and all the dynamics involved in crane and boom movement and raising, to be able to demonstrate information through oral, written and practical assessments and to be tested by a third party or in-house trained evaluator.

The post Importance of Proper Rigging and Signal Training appeared first on Perth Training Courses.

The licence will allow you to conduct basic rigging, intermediate rigging or advanced rigging (depending on your qualification) in any state or territory of Australia.

A High Risk Work Licence (HRWL) issued by the National Commission for the Certification of Crane Operations (NCCCO) is valid for 5 years and makes you a qualified basic rigger, intermediate rigger or advanced rigger for that time period. You must be at least 18 years of age before you can receive a High Risk Work Licence. You can complete a rigging and dogging course in Perth, Western Australia.

How Long is a Rigger Certification Good For?

Your rigging certification is valid for a period of five years. Once your license has expired, you must not conduct high-risk work until you have renewed your high-risk work licence.

You need to keep your contact details up to date so that you can receive alerts when your license expires.

What Happens if My Rigging Certification Expires?

You have 24 months to renew your basic rigging, intermediate rigging or advanced rigging licene issued via NCCCO after it expires.

If you do not apply for a renewal within 24 months, the current high risk work licence (HRWL) cannot be extended and you will not be licensed or a qualified rigger.

Your HRWL will be revoked and you will not have the ability to to work as a rigger, signal person or complete any tasks covered by the ticket. You will need to be re-trained by the RTO (or assessed by a registered worksafe assessor before you can apply for a new high-risk job licence.

To renew your high risk work licence (HRWL), you will need:

• Your email address and mobile phone number
• Your High Risk Work License number and or card
• Payment method
• A digital passport style photo (taken within the last 6 months)

Contact Perth Training Centre to book your basic rigging, intermediate rigging or advanced rigging certification renewal or dogman and rigging courses with a registered worksafe assessor.

The post Do Rigging Certifications Expire in Australia? appeared first on Perth Training Courses.

Some companies use these words interchangeably to add to the confusion. Although a Rigger is frequently in a position to carry out all of the same duties as a Dogman with a High Risk Work Licence (HRWL), they often have more expertise and are protected by additional licenses that are unique to Rigging duties.

Below we’re going into depth about the differences between dogging and basic rigging so that you can determine if a dogman ticket test or rigging certification is best for you.

What is Dogging?

A Dogman or “dogger” is a specialist in slinging and guiding loads handled correctly by cranes. The Dogman must hold a High Risk Work Licence “DG.” The Dogman chooses the best equipment for slinging a certain load depending on the mass and the center of gravity.

In addition, they perform the purpose of guiding the crane operator when the load is not seen by the operator using a combination of radio contact, whistles, and hand signals. The crane operator would also operate with a team of dogmen – one on the ground to attach the load and another on the top of the building to lift it.

The dogmen ‘Dogger’ is responsible for the following on-site activity:

• Usage of slinging techniques.
• Determination of the weight of the load to be raised.
• Selection and testing of the lifting gear equipment.
• Directing of the operator of the crane in the movement of the load.
• Safe dogging practices.

What is Rigging?

A rigger can perform all the same activities as a Dogman can perform, as well as more advanced rigging techniques depending on the type of rigger licence they have.

Traditionally, basic rigging was someone who held a rigging licence and used hoists and pulleys. More recently, the construction industry has extended the term rigging to include the use of mechanical load shifting equipment, including:

• Moving, positioning, or securing a load using a mechanical load shifting system.
• Dismantling or erecting a structure, crane or hoists.
• Safe placement of crane lift loads
• Installing static lines, safety nets and cantilevered crane loading platforms
• Mechanical load shift equipment comprises equipment such as cranes, hoists, chain blocks, and winch systems.

Frequently Asked Questions About Dogging and Rigging

The post What is the Difference Between Dogging and Rigging? appeared first on Perth Training Courses.

One of the most important tasks for which the ‘rigger’ will be responsible is the safe raising and rigging of various materials.

These materials must be safely lifted off the ground and elevated to various elevations based on the specifications of each project.   It is important for both the crane operator and rigger to understand the fundamentals of crane rigging and how lifting materials of different shapes and sizes at various angles can have a direct effect on the type of crane and rigging equipment needed.

This goes beyond understanding how to attach the rigging to the crane. The operator must be completely aware of the operation of the crane, its maximum load limits, and other such factors. The crane itself must also be in good working order without any defects whatsoever. Otherwise, if there is a lack of operator expertise or equipment efficiency, it may lead to extreme, expensive and hazardous incidents.

To learn more about what the basics of dogging and rigging are or to secure your future in the industry enrol in a basic rigging course in Perth.

What’s Crane Lifting & Rigging Used For?

Lifting and rigging are most commonly done with portable or mobile cranes. There may be all-in-one cranes, where the crane is mounted on the back of a large truck-like vehicle or is a portable vehicle of its own.

Some cranes are semi-permanent structures, where the crane is transported to the construction site and then set up in a specific position where it can provide the most value. For example, in the case of high-rise construction projects, a Spyder crane may be temporarily mounted on the upper floors of the structure and relocated regularly as the height of the building increased.

The primary function of lifting and rigging is to move critical equipment and materials to places where they are easily accessible to staff. This method helps to reduce the risks of needing to move scaffolding equipment and materials manually, which can be complicated and hazardous.

In addition, lifting and rigging were designed to lift extremely heavy loads that would otherwise be difficult to handle manually. For example, a heavy portable generator needs to be raised up to ten floors where staff can use it to supply electricity. Manual transport of the generator is not feasible due to the weight of the generator.

In addition, the generator must be correctly rigged in order to allow offsets in load-bearing limits that adjust on the basis of the angle of the generator as ten stories are lifted. In our example, the best option would be to use a mobile crane. The crane could quickly lift the generator after it had been correctly rigged and attached to the crane.

Security of Rigging Equipment

Lifting and rigging require proper safety measures to ensure a safe working environment. In the case of construction firms owning their own cranes, it is important that routine maintenance is carried out to ensure that all parts, including the lifting mechanism, are in good working order.

When companies want to employ cranes for projects, they need to use a reputable and reliable company. It is perfectly appropriate for the project manager or the person responsible for securing the crane to request maintenance reports to demonstrate that the crane has been well maintained.

If you own your own crane or hire one, the next safety measure, once you have it on the job site, is to ensure that it is correctly set up before it is lifted. Mobile crane trucks must be adequately supported to prevent them from falling over due to shifts in the center of gravity when materials and equipment are raised and transferred.

Supports are also part of a crane truck and can be extended and lowered in place. Until deploying the supports, called outriggers, the cranes should be parked on a level and stable floor. Outriggers must also be on stable ground to keep the crane from falling over or collapsing into the soft ground. In the past, there have been incidents where the crane was not level or the floor on which it was parked was not secure.

If the crane is fully parked, supported, and configured, the next safety measure is to decide the most suitable rigging construction system to be used. There are various types of sling and hitch configurations that could be used, depending on the type of lift required, as follows:

The Different Types of Rigging Configurations

Basket Hitching – This approach is where each end of the sling is attached to the hook of the crane. It helps prevent the added burden on the load. Depending on the size of the object being raised, a single or double wrap sling configuration can be used. However, this approach is not so perfect to use with items that are difficult to keep balanced.

Choker Hitching – The sling is wrapped around an object, then tightened to hold it in place. This method of lifting is well suited for large cylinder items, but it should be lifted one at a time, not in loose bundles.

Vertical Hitching – This form is where one end of the sling is tied to the crane and the other to the item to be raised. However, one common problem is that an object can start rotating and rotate freely when it is lifted, so this approach is almost never used with a crane. Variations using other techniques can be used to make vertical lifting safer and safer.

If the rigging method has been determined, the next thing the operator would need to know is the weight of the materials or equipment to be lifted. Slings have overall stress limits for their weight. Exceeding these could cause the slings to snap and break, causing the object to fall to the ground below.

The operator must also realize that, as the angle increases, the overall tension limits also change, causing even higher rigging weight limits. To explain the results, let’s look at how the maximum stress changes:

90 degrees (vertical lift) – At this angle, the weight is evenly distributed, so if you were to lift a 1,000-pound object and use a dual configuration of two slings, each with a 500-pound maximum, it would be secure to lift the object.

60 degrees – At this angle, the performance of the slings is reduced to 86.5 percent of the full load limits. In other words, each sling now supports a maximum of 432.5 pounds or a total of 865 pounds. But it wouldn’t be safe to lift a 1,000-pound piece.

45 degrees – At this angle, the performance of our dual-sling setup is reduced to 70% of the maximum load limits. Now, each sling can only carry a total of 350 pounds or 600 pounds. Again, the lifting of a 1,000-pound weight will be risky.

As you can see, as the degree of lift increases, the load-bearing stress decreases. As a result, using our example, higher rating slings or additional slings will be needed to lift this load safely.

Please keep in mind that these are just general examples for comparison purposes, and other factors can affect load stress. It is your duty, as an operator, to educate yourself and learn how to correctly measure load limits and stress to ensure safe rigging and raising of the crane. Learning and following company procedures will help mimimise the risk of human error or accidents involving employees and other workers onsite. 

The post Crane Lifting Basics – Dogging and Rigging Basics appeared first on Perth Training Courses.

Like all lifting activities, hoisting and rigging should be carried out with employee safety as the primary objective. In order to comply with health and safety regulations in accordance with industry expectations, companies should carefully consider the following two elements:

Before the lifting applications begin on job sites, the crane operator and ground rigging teams should carefully consider the specifications of the lift, carry out a detailed risk assessment and adhere to the safety standard of the rigging operation.

The first point would be to ensure the dogging and rigging team are all certified with a valid High Risk Work Licence or are certified as at least an Australian intermediate rigging standard course. Ideally the rigging crew should hold an advanced rigging certificate. If you are unsure, check to see if your team needs dogging and rigging courses in Perth.

The team of riggers must ensure that the overall rigging configuration and the individual elements are appropriate for the size and weight of the load in question, in order to avoid overloading the equipment which could lead to harm and severe safety hazards. In order to ensure that the products are of the appropriate standard and quality, the rigging equipment itself should also be purchased from reputable suppliers. Items should then be routinely inspected to ensure that they continue to follow safety requirements in order to preserve this quality.

Rigging Equipment Includes:

There are a range of lifting equipment used in rigging. Below is a selection of rigging equipment used in Australia. Rigging equipment can differ depending on the type of rigging and lifts the organisation is undertaking.

Slings:

Slings are used in combination with a lifting device, such as an overhead crane, hoist, or forklift to lift loads of heavy equipment. The sling is wrapped around the load, then attached to the crane hook with ropes or chain to a shackle. Sling material can range from steel to synthetic slings.

Chainslings:

Chain slings deliver a durable lifting solution that comes with a handy hook system for quick attachment. Slings are available in single, 2 leg and 4 leg designs and a range of different weight limits.

Spreader Beam:

Spreader beams are a versatile lifting solution designed to be used in a number of configurations, depending on the specifications of the lifting process. Both synthetic lifting slings and wire rope slings may be used for these beams.

Rigging Screws:

Rigging screws are important pieces of equipment for industrial lifting applications. It is designed to have tensioning capabilities for adjustable lengths. We store rigging screws in different lengths and tensile strengths to suit your needs.

Nuts and eye bolts:

We store eye nuts and eye bolts to help with your heavy lifting requirements. Ideal for rigging applications involving industrial lifting, our lifting eye nuts and bolts are available in different grades to satisfy your challenging lifting requirements.

Turnbucks:

The Rigging screws are used to adjust the tension and length of the wire line. Turnbuckles are used in the same way as rigging screws. One notable difference, however, is that rigging turnbuckles are usually smaller in size and offer shorter adjustment choices. The useful aspect of rigging turnbuckles is that they can be balanced under load.

Shackles:

A shackle is a U-shaped metal parts with a pin along the non-curved side used in rigging applications. We store both DEE and BOW shackles that are used for various purposes. All shackles are galvanized, some are fitted with screw pins or safety pin locks and some are suitable for lifting purposes and some are not. Our shackles conforming to AS 2741 are suitable for lifting purposes.

Thimbles:

In rigging applications, stainless steel rigging trunks are used to provide the underlying support for the wire rope when the eye loop is made and fastened. Commercial rigging thimbles prevent the wire rope from pinching and splitting in the eye, which helps to maintain its shape while in use and means that the wire rope lasts longer. Thimbles can be complemented by wire rope clips and swages.

Crane hooks:

Crane lifting hooks or rigging hooks are for grabbing and lifting heavy loads. They are attached to rigging hardware such as a hoist or a crane. Usually, the lifting hook is fitted with a safety lock to prevent the removal of the lifting wire rope sling, chain or rope to which the load is attached.

The post What is Rigging Equipment? Must Know For All Riggers appeared first on Perth Training Courses.

What is Rigging?

In order to insure the stability of those members, rigging work involves the use of mechanical load shifting equipment and associated gear to move, place or secure a load, including the plant, equipment or members of a structure. The setting up or dismantling of cranes or hoists is also included.

Why You Should Do a Rigging Course

Rigging is classified as a high-risk activity that requires a high-risk work licence for anyone intending to perform rigging work (HWRL). We deliver Basic Rigging and Dogging training at Nara Training & Assessing. Instead of boosting your career prospects by being eligible to perform both dogging and basic rigging work, we strongly recommend you to enrol in a combined Dogging and Basic Rigging course Perth. Read our Difference Between Dogging and Rigging blog post for more information.

Which Class of Rigging is Right For You?

There is a strong demand throughout Australia for licenced Riggers, particularly in Western Australia, which accounts for 25.2% of all Riggers in the nation (Source: Job Outlook). If you are looking to upskill and boost your career prospects, the answer might be a rigging training course. We’re giving you the run down on all you need to know about Rigging in this blog post to help you get started on this journey.

What are the Different Classes of Rigging?

In Australia, there are three kinds of rigging licences, each with its own description of the type of rigging work that can be carried out. Find out more about Perth dogging courses here.

High Risk Work License – Classes of Rigging License

Dogging Basic Rigging RB

Intermediate Rigging RI

Advanced Rigging RA

Basic Rigging

The Dogging License requirements are covered by a Basic Rigging licence. You must hold a dogging licence or be enrolled in a Combined Dogging and Basic Rigging training course to apply for a Basic Rigging licence. The scope of work for Basic Rigging includes:

Dogging work

Structural steel erection

Particular hoists

Placement of pre-cast concrete members of a structure

Safety nets and static lines

Mast climbers Perimeter safety screens and shutters

Cantilevered crane loading platforms

Intermediate Rigging

You need to have an Intermediate Rigging licence to participate in intermediate rigging work. You must hold or have previously passed an assessment for a Dogging License and Basic Rigging License to apply for an Intermediate Rigging licence. The scope of work for Intermediate Rigging includes:

Rigging work in the class Basic

Rigging All hoists

Rigging of cranes, conveyors, dredges and excavators

Tilt-slabs Demolition of structures or plant

Dual lifts

Advanced Rigging

You must have an Advanced Rigging licence to perform Advanced Rigging work. You must hold or have previously passed an assessment for a Basic Rigging Dogging License or an Intermediate Rigging License in order to apply for an Advanced Rigging licence.

The scope of work for Advanced Rigging includes:

Rigging work in the class Intermediate Rigging

Rigging of gin poles and shear legs

Flying foxes and cableways

Guyed derricks and structures

Suspended scaffolds and fabricated hung scaffolds

The post Which Class of Rigging is Right for You appeared first on Perth Training Courses.

A recent survey of more than 1,400 individuals found that almost half of them (49 percent) did not believe their employer offered them sufficient training programs for learning and development.

Here are 8 reasons why it is important for workplace training programs, and here’s how to make it a key focus of your business strategy and managers.

Better Performance by Employees

This goes almost without saying, but any employee who receives employee training to advance their skills and education will be able to do their job better, of course. This applies to all industries, departments and employee levels within your company.

You may also find that the trust of your staff improves through regular employee training programmes, as they gain a much stronger understanding of your industry, the purpose of the company and the responsibilities of their own work.

Increased capacity for new technologies and methods to be adopted
The building industry is changing constantly. It is essential that your staff are constantly up to date with the standards and policies of the industry! It makes it easier for staff to embrace any changes with consistent training.

Wider Understanding of the Company

Make sure you create a collaborative environment that encourages members of each team to learn from others if your organisation consists of multiple different departments. Do not be afraid to open it up to the wider company if one team is holding a training session. You may be surprised at who wants to attend and learn a bit more about an area of the company with which they have not been involved at all.

If your employees can see the wider picture, they will naturally feel more accountable and driven to achieve the overarching goals of your company.

Increased capacity for new technologies and methods to be adopted
The building industry is changing constantly. It is essential that your staff are constantly up to date with the standards and policies of the industry! It makes it easier for staff to embrace any changes with consistent training.

Lower Turnover of Personnel with Employee Training

Within your organisation, some personnel turnover is normal. Many people would even say that having new faces bringing fresh ideas to a business is healthy for an organisation. But for your organisation, high employee turnover can mean large amounts of disruption and wasted money. A far more efficient way to spend your money is to invest in training (rather than on recruitment costs). Your staff will feel more valued by learning new things that will help their career development, and are therefore more likely to stay loyal.

Before, we have spoken a lot about the significance of employee engagement, and it’s something that should not be underestimated. Nor should the effect of a lack of training and development on the engagement and ambition of a person be affected. The majority of your staff will greatly value and appreciate the opportunity to learn, rather than stagnant and uninspiring, they want to work in a place where things feel fresh. If they do the same thing day-in, day-out, without excitement on the horizon, their levels of motivation will nosedive.

Increased workplace satisfaction and morale among workers
Investing in training time, money and resources makes your staff feel valued. Employees who are appreciated and challenged by training opportunities are more likely to feel satisfied with their work, increasing overall morale!

Developing a Company

Regular training sessions make sure your teams stay ahead of the curve; ideal for any SME looking to beat the competition. Encourage your various departments to keep regular tabs on any developments in their specific niche and have them do a presentation on it for anyone else who is interested if someone spots something particularly interesting. This way, you will always stay ahead of the curve, offering your clients the very best service.

Enhance your Bottom Line

To boost the bottom line of your company, maintaining high levels of employee engagement is crucial, but better internal training also contributes in another way. It’s only logical that they will be better at their jobs by improving the skills of your staff, whether that’s customer service or administration, which means more business for you.

From forklift training and dogging in Perth to a basic to an advanced rigging course

The post Why Employees Should Invest in Training appeared first on Perth Training Courses.

What is In This Guide?

What is a high-risk work licence?

Why are high-risk work licences required?

What Type Of Work Is Deemed To Be High Risk?

What are the eligibility criteria for a high-risk work licence?

What are the main types of high-risk work licences?

Dogger – DG

Intermediate Rigging – RI

Advanced Rigging – RA

Pressure Equipment Operation licences

Scaffolding Licence

What Are The Requirements For Training And Assessment?

What is a High Risk Work License Validity Period?

Why is it essential to work with a Registered Training Organisation (RTO)?

What is the importance of health and safety laws?

 How long are high-risk work licences valid for in Australia?

What Is A Licence For High-Risk Work?

Your High Risk Work License is a high-risk work permit that is required if you work with high-risk equipment or facilities. In every state and region, these licences are valid. The issue of all High-Risk Work Licenses (HRWL) is subject to evaluation by the newly released National Assessment Instruments against National Competency Units (NAIs).

Why Are Licences For High-Risk Work Required?

Construction is recognised as one of the most dangerous types of work, and when considering their working activities and the safety of their employees, health and safety at work is the first priority for many building and construction firms.

What Type Of Work Is Deemed To Be High Risk?

To perform the following you require a High Risk Work License:

Source: https://www.safeworkaustralia.gov.au/description-high-risk-work-licences

What Are The Criteria For Eligibility For A High-Risk Work Permit?

A Registered Training Organization (RTO) must evaluate their training, skills, and knowledge using the appropriate assessment tool under practical workplace conditions before a person can apply for a national High-Risk Work Licence.

They are then able to make an application for the HRW licence class when a participant has achieved competence for the unit. Such licences shall be issued by the regulatory authority in the state in which the licence has been obtained.

What Are The Main Types Of Licences For High-Risk Work?

Licences for Crane and Hoist

Elevating Work Platform Boom Type-WPP

PB-Concrete placing boom

Mobile Slewing Crane 20t Capacity-C2

C66 Capacity Slewing Mobile Crane 60t

Mobile Slewing Crane 100t Capacity-C11

Mobile Slewing Crane over 100t capacity-C0

Crane Loading Vehicle-CV

CN Mobile Non-Slewing Crane

CT-Tower Crane

Dogger- DG

Dogging is the application of slinging techniques, including the selection and inspection of lifting equipment, for the movement of a load by means of a crane, hoist or other apparatus designed for use as a crane or hoist; or for the guidance of the operator by means of a lift, crane or other apparatus designed for use as a lift or crane when the load is transferred.

Basic Rigging-RB Basic Rigging-The work covers specific hoists, erection of structural steel, dogging work, placement of structural pre-cast concrete members, perimeter safety screens and shutters, mast climbers, safety nets and static lines, and platforms for cantilevered crane loading.

Intermediate-RI Rigging

Intermediate Rigging-Class Basic Rigging includes rigging work, all hoists, crane rigging, conveyors, dredges and excavators, tilt-slabs, structure or plant demolition, and dual lifts.

RA-Advanced Rigging

Innovative rigging (includes all intermediate rigging and involves suspended and fabricated hung scaffolds, flying foxes and cableways, gin poles and shear legs, guyed derricks, and structures). Learn more about dogging or advanced rigging course in Perth.

Licences for Pressure Equipment Operation

These are provided for the operation of the standard boiler operator, advanced boiler operation, reciprocating steam engine, and turbine.

Licence for Scaffolding

It involves the work of constructing, modifying or dismantling a temporary structure specifically designed to support platforms from which an object or individual may fall more than 4 m. The licences are divided into three types, namely:

Intermediate scaffolding (Cantilevered and spurred scaffolds, cantilevered crane-loading platforms, perimeter safety screens and shutters, barrow ramps, and sloping platforms, mast climbers tube and coupler scaffolds (including coupler covered ways, tube, and portals)). Advanced scaffolding (Hung scaffolds, including Suspended scaffolds, wire ropes or chains and scaffolds hanging from tubes)

What Are The Requirements For Training And Assessment?

Training and evaluation must be carried out under the supervision of or in partnership with a Registered Training Organization in accordance with the National Standard for Licensing Persons Performing High Risk Work (RTO). This must consist of structured training, practical training and experience, and the assessment of the skills of the trainee through the use of nationally approved assessment tools.

You must apply for your High Risk Work License within sixty days of issuing a Statement of Attainment from an RTO once this is completed (or a Notice of Satisfactory Assessment issued by an assessor). Failure to do so may result in you being required to be reassessed by the licencing authority. On your behalf, Nara Training will submit your licence.

What is a High Risk Work License Validity Period?

Since High Risk Work Licenses are valid for 5 years only, it is important to keep your contact details up to date so that when your licence is due to expire, you can receive reminders. Until you have renewed your high-risk work licence, you must not perform high-risk work once your licence has expired.

You have 24 months to renew your licence after your licence expires. If the renewal application is not submitted within 24 months, the current HRWL cannot be renewed and you will not be licenced. Before you can apply for a new high risk work licence, your HRWL will be cancelled and you will have to be re-trained by an RTO.

Renewing Your High Risk Licence

You will need to have the following prepared in order to renew your HRWL:

Your number for High Risk Work License

Your email address and number for mobile phones

To make a payment, your debit or credit card

Clear digital images taken in the last 6 months (head and shoulders only)

What are the fees associated with obtaining a licence for high risk work?

The following are the renewal fees as of today and until 30 June 2020:

New licence: $100 New licence: $100

Class addition: $78.50 $78.50

License renewal: 53 dollars

Lost or Stolen License replacement: $66 Nara Training & Assessing

It is a Registered Training Organization (RTO 4518) offering accredited training in the workplace in accordance with national competency units. In the Perth Metro area and the South West of WA, we have purpose-built facilities as well as an additional ability to deliver on-site in Western Australia.

Why is working with a Registered Training Organization (RTO) essential?

RTOs provide accredited VET qualifications The students are offered nationally approved training that equips them with everything they need to succeed in their chosen field of industry.

The RTO ensures the high quality of the skills and knowledge taught and remains relevant to future employers and the industries involved.

The post Guide to High Risk Licenses in Australia appeared first on Perth Training Courses.

Height Safety and Confined Space Rigging Equipment

This equipment needs to be visually inspected by a “competent person”  or inspector at least every 6 months. For many fall arrest blocks and inertia reels/ winches, the manufacturer will have a recommended service schedule on top of the regular visual inspections. Servicing involves sending the unit back to the manufacturer where they pull apart and thoroughly check that everything is in full working order, additionally making any repairs where needed. Servicing can be required anywhere from yearly to every 5 years, this varies from supplier to supplier and the individual device.

Round and Web Lifting Slings

These types of slings need to be visually inspected  and tested for issues by a “competent person” at a minimum of every 3 months.

Concrete Clutch/ Concrete Lifter

Concrete clutches need to be load tested every 12 months.

Your Rigging Equipment may need to be inspected at shorter intervals depending on how often it is used.

As with everything, there are some items that don’t fit inside these general categories or that might have specific requirements. There are also some sites that may have additional safety procedures.

Always check over your gear before you go to use it, as it may not be in the same condition since it’s last use.

Tip:If it doesn’t look the same, is really dirty, rusty, the hook doesn’t close or the mechanism doesn’t lock it’s probably no good to use. If you’re ever unsure about your rigging equipment, here at All Lifting we are all about keeping you safe. Our safety inspectors can provide you with peace of mind to ensure you are meeting requirements.

What Equipment Needs to be Tagged?

There is a whole range of lifting equipment that must be inspected and tagged, for example – harnesses, lanyards, shackles, wire rope and lifting chains and slings. We recommend checking with the Lifting Equipment Engineers Association (LEEA) for a full list of gear that requires inspection, and the relevant Australian Standards.

Lifting Equipment Inspection Tags – Colour Code

In order to operate safely, all lifting, rigging and hoisting equipment must be inspected and tagged periodically throughout the year. These inspections should be performed every 3 months and the tags that are placed on the equipment represent which quarter of the year the test was performed in.

What’s on the lifting and rigging inspection tag?

The most commonly used lifting and rigging tags would be something like our Next Inspection Due Tag , which comes in the quarterly inspection colours of red, green, blue and yellow and includes a space to record the date of when the equipment requires inspection next.

These inspection tags can also be customised to suit your particular industry or needs – you can include options like pre-printed data and sequential numbers to aid with record keeping, or add a barcode or QR code to store more complex information without taking up too much space on the tag itself. View Custom Lifting & Rigging Tags.

The post Who Can Inspect Rigging Equipment? appeared first on Perth Training Courses.

Why Should I Do A Rigging Course?

You need to have both a rigging licence (either from a Certificate III in Rigging or a certificate of achievement from a Registered Training Organization) before being allowed to perform any type of rigging work, from working with hoists to gin poles and shear legs (RTO).

You will also receive a High Risk Work (HRW) licence as part of undergoing a rigging course, which is also a requirement to have before working on potentially dangerous worksites.

It should also be noted that you are also responsible for ensuring that all workers have adequate training, instruction, and information to properly perform rigging work if you are managing a building or worksite.

What Are Rigging Courses Like?

You are taking a 5 day Basic Rigging course at CTI, or 4 days for the Intermediate or Advanced courses. In order to participate, you’ll need appropriate Personal Protective Equipment (PPE).

Eight hours per day is the course itself. All of the training is performed at CTI, with no training offsite-CTI has everything on site required. The course is a combination of learning in practical and theoretical terms.

The rigging classes are not affected by the weather. For example, if there is rain, the trainees will wear protective coats and continue the training, although occasional breaks may occur in order to be practical.

Types of Riggering licences

This section deals with the following high-risk licences:

Basic rigging work (RB)
Intermediate rigging work (RI)
Advanced rigging work (RA) (RB)

If you work in the lift and escalator sector, there may be a requirement to hold a Rigger or Dogger licence. Learn more about the types of Dogging and Rigging course below;

Basic Rigging Work (RB)

The requirements for a dogging licence encompass a basic rigging licence. You must hold or have previously passed an assessment for a dogging licence in order to apply for a basic rigging licence. The scope of work for basic rigging includes:

• dogging work
• safety nets and static lines
• mast climbers
• perimeter safety screens and shutters
• cantilevered crane loading platforms.
• structural steel erection
• particular hoists
• placement of pre-cast concrete members of a structure

Rigging Intermediate – RI

To perform intermediate rigging duties you need to have an intermediate rigging – ri high risk work licence.

• To apply for an intermediate rigging licence you must hold, or have previously passed assessment for, a dogging licence and basic rigging licence.
• The scope of work for intermediate rigging includes:
• Rigging work in the class basic rigging
• All hoists
• Rigging of cranes, conveyors, dredges and excavators
• Tilt-slabs
• Demolition of structures or plant
• Dual lifts.

Advanced Rigging – RA

You need an Advanced Rigging – RA High Risk Work License to perform advanced rigging tasks.You must hold, or have previously passed an evaluation for, a dogging licence, basic rigging licence and intermediate rigging licence to apply for an advanced rigging licence.

• Rigging work in the class Intermediate Rigging
• Guyed derricks and structures
• Suspended scaffolds and fabricated hung scaffolds.
• Apply for a high risk work licence
• Rigging of gin poles and shear legs
• Flying foxes and cableways

What’s Its Like to Be a Rigger?

Using rigging gear such as pulleys, cranes and winches, riggers move heavy materials and equipment around worksites. On construction sites, they assemble temporary structures like scaffolding and move and assemble pre-cast facades and panels on buildings under construction.

Usual Tasks and Responsibilities of a Rigger

• Estimating the size and weight of the objects to be moved and deciding whether to use suitable equipment.
• Crane erections, mobile crane booms and height adjustments for tower cranes
• Scaffolding components for lifting, positioning and bolting to build up.
• Attaching sling equipment for lifting loads.
• Following Occupational Health & Safety (OHS) procedures in the workforce.
• Cords, ropes, pulleys, winches and other lifting tackles are installed and operated.
• To inspect, maintain and repair equipment.
• Lifting and erecting of steel, glass or concrete prefabricated panels.
• On buildings under construction, erecting structural steel.
• In a team environment, Riggers enjoy practical work and working outdoors. They are physically fit and conscious of safety, and are usually used in the industries of construction, mining, shipbuilding and manufacturing.

Personal Requirements for a Rigger

• Enjoy practical work in the outdoors
• Able to deal with the job’s physical demands
• Capable of working at heights
• Good for hands
• Security-conscious
• Capable of working as part of a team

Training & Education for a Rigger

You usually have to obtain a licence to perform high-risk work to become a rigger. You will need to complete competency units at an approved Registered Training Organization and work under the supervision of a licenced operator in order to gain a licence.

To record skills accomplished during training, you will also need to keep an approved logbook. Evaluation by an accredited appraiser will then be required. Under the National Standard for Licensing Persons Performing High Risk Work, the High Risk Work Licence is granted. You can also, through an apprenticeship or traineeship, become a rigger. Entry requirements may differ, but Year 10 is generally required by employers.

The post What Qualifications Do You Need to be a Rigger? appeared first on Perth Training Courses.